|
Title: Way to spread out formation? Post by: Rends on October 09, 2011, 09:50:58 AM Is there a way to spread out a AI platoon while driving in a column?
I could need that for a mission where a column is driving on a road and when the first tank stop the other 2 doesn´t and try to overtake or leave the column formation. Title: Re: Way to spread out formation? Post by: Mistwalker on October 09, 2011, 04:37:18 PM Is there a way to spread out a AI platoon while driving in a column?I could need that for a mission where a column is driving on a road and when the first tank stop the other 2 doesn´t and try to overtake or leave the column formation. Can't you set the event that triggers spread-out formation?Title: Re: Way to spread out formation? Post by: Rends on October 09, 2011, 06:14:36 PM Is there a way to spread out a AI platoon while driving in a column?I could need that for a mission where a column is driving on a road and when the first tank stop the other 2 doesn´t and try to overtake or leave the column formation. Can't you set the event that triggers spread-out formation?Title: Re: Way to spread out formation? Post by: Rends on October 10, 2011, 07:09:55 PM No other ideas?
I have the problem that at least 1 out of 3 AI Pz.II will fall into water from a bridge because they drive so close together that one will do an "evasive" manouvere while on the bridge. Title: Re: Way to spread out formation? Post by: Iceman on October 10, 2011, 11:27:19 PM No other ideas? This bridge from one of the original maps?I have the problem that at least 1 out of 3 AI Pz.II will fall into water from a bridge because they drive so close together that one will do an "evasive" manouvere while on the bridge. Title: Re: Way to spread out formation? Post by: Rends on October 11, 2011, 12:39:20 PM Bridge is original while the map is my own work.
Will release the first Barbarossa mission later the day so everyone can check it. Hope it can be fixed. Title: Re: Way to spread out formation? Post by: Iceman on October 12, 2011, 09:01:42 AM Bridge is original while the map is my own work. On your map special "bad zones" around the bridge have been added?Will release the first Barbarossa mission later the day so everyone can check it. Hope it can be fixed. (http://i260.photobucket.com/albums/ii29/1c3mn/sf_editor/th_sf_kh42_faq_editor_bridge.jpg) (http://i260.photobucket.com/albums/ii29/1c3mn/sf_editor/sf_kh42_faq_editor_bridge.jpg) Example of the bridge http://www.4shared.com/file/KuGnhyV3/most_02.html in folder data - generated map most_02.datapack - packed source map most_02_mission.datapack - empty mission for this map It's quite difficult object. It's true :)P.S. If you want, you can send me in PM the source file of map for check of correctness of installation of the bridge. Title: Re: Way to spread out formation? Post by: Rends on October 12, 2011, 07:36:59 PM Ok, the dl link can be found in this thread:
http://graviteam.com/forum/index.php?topic=9702.0 (http://graviteam.com/forum/index.php?topic=9702.0) Title: Re: Way to spread out formation? Post by: Kyth on October 14, 2011, 12:40:34 PM I've gotten good results by making a few small changes: - Set the absolute height of the ramps to 4.5m - Set the height of the riverbed where the bridge is sited, to 1.5m. - Extended the 'no-go' zone a little further inland. You could try it out the new datapack (map needs regeneration): http://www.4shared.com/file/CawXtWz4/Rends2.html (http://www.4shared.com/file/CawXtWz4/Rends2.html) Title: Re: Way to spread out formation? Post by: Rends on October 14, 2011, 08:26:10 PM Thx Kyth, i will try your file out.
Title: Re: Way to spread out formation? Post by: Rends on October 14, 2011, 11:40:38 PM Kyth, can you explain exactly what you have done because i can´t generate the datafile you uploaded. The ME doesn´t recognise it .
Title: Re: Way to spread out formation? Post by: Kyth on October 15, 2011, 12:48:45 AM 3 things: 1. Height of 'Rampe1' and 'Rampe2' set to 4.5m (absolute) (https://lh4.googleusercontent.com/-hNyqpmX6TLY/TpjZBMuTH5I/AAAAAAAAAdg/b-Md0n04O5U/s800/Rends1.jpg) 2. Height of riverbed ('Ramp3') set to 1.5m (absolute) (https://lh3.googleusercontent.com/-I9El5H8YOJ8/TpjZB-DfGTI/AAAAAAAAAds/p1ppkbqI5N0/s800/Rends2.jpg) 3. 'No_water' and 'No_water2' extended inland by 1 or 2 m: (https://lh4.googleusercontent.com/-DaqwIeOW_zc/TpjZA7tkdPI/AAAAAAAAAdc/HvXazawRkvk/s800/Rends3.jpg) Title: Re: Way to spread out formation? Post by: Rends on October 15, 2011, 05:16:29 PM Thx Kyth!
Title: Re: Way to spread out formation? Post by: Iceman on October 15, 2011, 11:35:28 PM Ok, the dl link can be found in this thread: polygon with some fixhttp://graviteam.com/forum/index.php?topic=9702.0 (http://graviteam.com/forum/index.php?topic=9702.0) http://www.4shared.com/file/0eypURoV/Rends2_poly.html Rends2_poly.datapack - packed map \data\ - unpacked source and generated polygon Small error. Tactical property "bridge" is an impassable (forbidden) zone for all (it sounds illogically, but it's true :)) Has corrected in properties of a point of the bridge-> tactical property "bridge"-> to "road" Has added some tactical zones around the bridge And Kyth rights - try to use for the bridge absolute values of heights P.S . And sorry again for my English :) |